 |
|
| |
|
|
业务洽谈：
联系人：张顺平
手机：17727550196（微信同号）
QQ:3003262363
EMAIL:zsp2018@szczkjgs.com
联系人：鄢先辉
手机：17727552449 （微信同号）
QQ:2850985542
EMAIL:yanxianhui@szczkjgs.com
负责人联络方式：
手机：13713728695（微信同号）
QQ:3003207580
EMAIL:panbo@szczkjgs.com
联系人：潘波 |
|
|
| |
|
 |
|
 |
当前位置：首页 -> 方案设计 |
|
|
| ST powerSTEP01系统级封装(SIP)步进马达驱动方案 |
|
|
| 文章来源： 更新时间：2015/5/25 15:22:00 |
|
ST公司的powerSTEP01是集成了8路16 mΩ MOSFET的系统级封装(SIP)步进马达驱动器,包括有SPI可编程控制器,提供马达群数字控制.器件工作电压高达85V,最大输出电流10A,多达1/128微步距,具有SPI接口,过流保护和超温保护,主要用在大功率双极步进马达如舞台照明,监测系统,纺织和缝纫机,PCB贴片机.本文介绍了powerSTEP01主要特性,框图和典型应用电路,以及演示板EVLPOWERSTEP01主要特性和主要指标,电路图和材料清单与PCB主要元件布局图.
The powerSTEP01 is a a system-in-package integrating 8 N-channel 16 mΩ MOSFETs for stepper applications up to 85 V with a SPI programmable controller, providing fully digital control of the motion through a speed profile generation and positioning calculations. It integrates a dual low RDS(on) full bridge with embedded non-dissipative overcurrent protection.
The device can operate with both voltage mode driving and advanced current control fitting different application needs. The digital control core can generate user defined motion profiles with acceleration, deceleration, speed or a target position easily programmed through a dedicated register set. All application commands and data registers, including those used to set analog values (i.e. current protection trip point, deadtime, PWM frequency, etc.) are sent through a standard 5-Mbit/s SPI. A very rich set of protections (thermal, low bus voltage, overcurrent and motor stall) make the powerSTEP01 “bullet proof”, as required by the most demanding motor control applications.
powerSTEP01主要特性:
Power system-in-package integrating a programmable microstepping controller and 8 N-channel power MOSFETs.
Operating voltage: 7.5 V - 85 V
Dual full bridge with RDS(on) = 16 mΩ
10 Ar.m.s. maximum output current
Adjustable output slew rate
Programmable speed profile
Up to 1/128 microstepping
Sensorless stall detection
Integrated voltage regulators
SPI interface
Low quiescent standby currents
Programmable non-dissipative overcurrent protection
Overtemperature protection
powerSTEP01应用:
High power bipolar stepper motor
– Stage lighting
– Surveillance systems
– Textile and sewing machines
– Pick and place machines
图1. powerSTEP01框图
图2. powerSTEP01典型应用电路-电压模式
图3. powerSTEP01典型应用电路-电流模式
演示板EVLPOWERSTEP01
The EVLPOWERSTEP01 demonstration board is a microstepping motor driver delivering up to 10 Ar.m.s.. In combination with the STEVAL-PCC009V2 communication board and the evaluation software, the board allows the user to investigate all the features of the powerSTEP01. In particular, the board can be used to check the performance and to regulate the parameters in order to fit the application requirements.
The EVLPOWERSTEP01 supports the daisy chain configuration making it suitable for the evaluation of the powerSTEP01 in multi motor applications.
演示板EVLPOWERSTEP01主要特性:
Voltage range from 10.5 V to 85 V
10 Ar.m.s.maximum output current
Up to 1/128 microstep
Programmable speed profile and advanced commands
Adjustable output slew rate
SPI with daisy chain feature
FLAG and BUSY LED indicators
Flexible supply voltage management
Suitable to be used in combination with STEVAL-PCC009V2
图4. 演示板EVLPOWERSTEP01外形图
演示板EVLPOWERSTEP01主要指标:
图5. 演示板EVLPOWERSTEP01电路图(1)
图6. 演示板EVLPOWERSTEP01电路图(2)
演示板EVLPOWERSTEP01 材料清单:
图7. 演示板EVLPOWERSTEP01 PCB主要元件布局图 |
|
| |
| |
|
|
|
